# Measure and identify a carburetor’s size

Learn how to measure a carburetor's size from the throttle bore, venturi and mounting flange, then use those numbers to match a replacement.

A carburetor's size is identified by measuring its openings, not by reading a single number. The throttle bore and the venturi diameter give the size, and the mounting flange pattern tells you what will bolt on. Measurements in hand let you compare listings side by side and build a shortlist you can trust. 

- Measure the throttle bore across the throttle plate opening at the base of the carburetor.
- Measure each venturi at its narrowest point to find the airflow passage size.
- Record the mounting flange hole pattern so a replacement fits the intake.
- Use the measured numbers to compare airflow ratings between listings.
- Write every measurement down with its unit before you search for parts.
 

## Start with the throttle bore 

The throttle bore is the round opening at the base of the carburetor where air leaves for the engine. Measure across the bore with a caliper or a bore gauge, reading at the widest point. Keep the throttle plate closed so the opening stays a clean circle. 

A two-barrel carburetor has two throttle bores, and a four-barrel has four. Measure each one separately rather than assuming they match. Record every bore in millimeters or inches and note which unit you used. 

Throttle bore alone does not describe the carburetor's airflow, because the venturi inside restricts the passage. Use the bore as a fitting measurement and pair it with the venturi figures. Both numbers belong in the same note. 

- Close the throttle plate fully before measuring.
- Read the widest span of the bore with a caliper.
- Measure each barrel and label it primary or secondary.
- Write the value and the unit in your notes.
 

## Measure the venturi diameter 

The venturi diameter is the narrowest point of the air passage inside the carburetor body. Air speeds up as it passes this restriction, and that speed draws fuel into the airstream. The venturi size sets how much air the carburetor can flow. 

Measure the venturi with a bore gauge or a set of internal calipers reaching down the throat. Read the smallest diameter you can find in each barrel. On a multi-barrel body, primary and secondary venturis may differ. 

A venturi measurement is hard to take with the carburetor assembled, so some builders use a known airflow rating instead. Where you cannot reach the venturi, note that the figure is unverified. A listing without a venturi number or airflow rating leaves the size partly unknown. 
| Feature | What it tells you | How to read it | 
| Throttle bore | Opening at the base and fit to the intake | Widest span of the bore | 
| Venturi diameter | Airflow passage size inside the body | Narrowest point in each barrel | 
| Mounting flange | Bolt pattern and gasket fit | Stud spacing and hole count | 
| Airflow rating | Rated flow through the carburetor | Figure stated by the maker |  

## Check the mounting flange pattern 

The mounting flange is the flat base that sits on the intake manifold, and its pattern decides whether a carburetor bolts on. Measure the distance between the stud holes in both directions. Count the holes and note their shape and position. 

Flange sizes are grouped by pattern rather than by a single dimension. Two carburetors with the same bore can carry different flange patterns. A mismatch here stops the swap before airflow even matters. 

Compare the gasket footprint as well as the holes, because the opening in the gasket must clear the throttle bores. Place the gasket on the flange and check that nothing overlaps. Record the pattern with your bore and venturi notes. 

- Measure stud spacing front to back and side to side.
- Count the mounting holes and sketch their layout.
- Check the gasket opening against the throttle bores.
- Note the flange pattern in the same record as the bores.
 

## Use the airflow rating as a cross-check 

An airflow rating is a figure a manufacturer states for how much air the carburetor passes, often in cubic feet per minute. The rating depends on the test pressure and the venturi size, so it is not a direct physical dimension. Treat it as a comparison figure, not a measurement you take yourself. 

A stated airflow rating helps when the venturi sits out of reach. Check that the rating matches the venturi and bore you measured before you rely on it. A rating with no stated test condition tells you little about the carburetor. 

Two carburetors can share a bore size and still carry different ratings because of their venturis. Use the rating to sort listings, then confirm with the physical numbers. The measured bore and venturi remain the facts you can verify. 

## Record measurements so they compare 

A measurement note needs the dimension, the unit and the location on the carburetor. Write each figure in the same unit so listings line up side by side. Mixing inches and millimeters across a shortlist invites a wrong match. 

Photograph the caliper reading next to the part it measures, and keep the image with the note. Label each barrel and each flange dimension clearly. A written record makes a second measurement easy to check. 

Keep the notes with the listing you are considering, not in a separate file. Add the airflow rating when a seller states one, and mark it as unverified. The completed record is what you compare across options. 

- Write the dimension, unit and location together.
- Convert all figures to one unit before comparing.
- Photograph each reading beside the part measured.
- Mark any figure taken from a listing as unverified.
 

## Match a replacement to your numbers 

A replacement carburetor fits when its flange pattern matches the intake and its bores clear the gasket. Compare the bore and venturi to the original rather than to a claimed equivalent. A close flange fit with different venturis changes how the engine runs. 

Sort candidate listings by flange pattern first, since a wrong pattern rules a part out. Then compare throttle bore and venturi figures within that group. The airflow rating comes last as a tiebreaker between close options. 

A carburetor swap affects fuel mixture, and jetting may need adjustment by a trained technician. Do not assume a larger bore improves output without supporting changes. State any uncertainty in your shortlist so the decision stays clear. 

## Where measurement gets uncertain 

Some carburetors hide their venturi behind castings or boosters, and a caliper cannot reach the narrow point. In that case, rely on a manufacturer's airflow rating and say the dimension is unconfirmed. Never list a guessed figure as a measurement. 

Worn throttle shafts and damaged bores distort a reading, so inspect the part before you measure. Clean the flange face so the caliper sits flat. A dirty surface adds error to every dimension taken from it. 

Where a job needs the carburetor removed, rebuilt or jetted, hand it to a trained technician. Measuring an installed carburetor can be done in place, but internal work carries risk to fuel systems. Your shortlist can still record the external dimensions safely. 

## Carburetor Size Measurement Questions 

### How do I measure a carburetor's size? 

Measure the throttle bore across the opening at the base, then measure each venturi at its narrowest point. Add the mounting flange stud spacing and hole pattern to the record. Those figures together identify the carburetor's size and fit. 

### Is throttle bore the same as venturi diameter? 

No, throttle bore and venturi diameter are different measurements. The bore is the opening at the base of the carburetor, while the venturi is the narrow restriction inside the air passage. Both are needed to describe the size. 

### What does the mounting flange tell me about a carburetor? 

The mounting flange tells you whether the carburetor will bolt to a given intake manifold. Measure the stud spacing in both directions, count the holes and check the gasket opening. A matching flange pattern is a fit requirement, not an airflow figure. 

### Can I use an airflow rating instead of measuring? 

An airflow rating can stand in when the venturi cannot be reached, but only as a stated comparison figure. The rating depends on the test pressure and the venturi size, so it is not a substitute for a physical measurement. Record it as unverified when a seller provides it. 

### What tools do I need to measure a carburetor? 

A caliper or bore gauge covers the throttle bore and the venturi, and a tape or rule handles the flange spacing. A gasket helps check the flange opening. Clean the surfaces first so each reading reflects the part. 

### What if the venturi cannot be reached with a gauge? 

A blocked venturi means the internal size stays unconfirmed from direct measurement. Use the maker's airflow rating and mark it as unverified in your notes. Ask a trained technician before disassembling the carburetor to reach the passage.
