How to measure vehicle overhang and maximum overhang
Learn how to measure front and rear vehicle overhang from the axle to the body, and what maximum overhang depends on for a ute or any other vehicle.
Contents
- What overhang means on a vehicle
- Tools and preparation before you measure
- Measuring front overhang step by step
- Measuring rear overhang step by step
- What sets the maximum overhang
- Maximum overhang on a ute
- Accessories that change the rear figure
- Recording figures for a shortlist
- Questions about vehicle overhang
- How do I do a vehicle overhang measurement at home?
- What is the maximum overhang on a vehicle?
- What is the maximum overhang on a ute?
- What is the maximum overhang on a vehicle in the UK?
- Does a tow bar count toward rear overhang?
- Why does long rear overhang matter when driving?
Vehicle overhang is the distance from a vehicle's axle to the furthest point of its body at that end. You measure front overhang from the front axle to the front-most body point, and rear overhang from the rear axle to the rear-most body point. The maximum overhang allowed depends on the vehicle class, the body type and the regulations that apply where the vehicle is registered.
- Measure overhang from the axle center to the furthest body point, not from the bumper to the ground.
- Front and rear overhang are measured separately and can differ a lot on the same vehicle.
- A ute or pickup often carries a long rear overhang once a tray or tow bar is fitted.
- Maximum overhang is set by regulation and by the vehicle's design, so confirm the figure for your class and location.
- Keep your measured figures beside listing details so you can compare vehicles on equal terms.
What overhang means on a vehicle
Vehicle overhang is the horizontal distance from an axle to the furthest part of the body beyond it. The front overhang runs from the front axle forward, and the rear overhang runs from the rear axle backward. Overhang shapes how a vehicle turns, clears ramps and fits into a parking space.
Overhang is not the same as overall length. Overall length spans the whole vehicle, while overhang covers only the part that sits beyond an axle. Two vehicles of equal length can carry very different overhangs.
The term also appears in load carrying, where cargo can extend past the rear of the body. Load overhang is a separate idea from body overhang, and rules treat it differently. Know which figure a listing or form is asking for before you measure.
Tools and preparation before you measure
A vehicle overhang measurement needs a flat surface, a tape measure long enough for the body, and a way to mark a vertical line. A plumb line or a straight edge dropped from the body point helps you project it onto the ground. Chalk or tape marks the reference points so the tape stays straight.
Park on level ground and check the tire pressures first, because a low tire changes the ride height and the body point. Remove loose items from the tray or trunk that could shift the body. Keep the vehicle unladen unless the rules you follow ask for a loaded figure.
Work with a helper where you can, since one person holds the plumb line while the other reads the tape. Write each figure down as you take it instead of relying on memory. A second measurement of the same point catches a slipped tape.
Measuring front overhang step by step
Front overhang is measured from the center of the front axle to the furthest forward point of the body. Drop a plumb line from the front bumper or body edge to the ground and mark that spot. Then find the axle center and measure the straight horizontal distance between the two marks.
Finding the axle center takes care, because the wheel arch does not show it. Look for the center cap of the wheel or the axle hub as a reference point. Measure to the same point on both sides and take the average if the body is not perfectly square.
Keep the tape parallel to the ground along the vehicle's centerline. A tape that runs at an angle adds length that is not really there. Record the front figure on its own line so it is not confused with the rear measurement.
Measuring rear overhang step by step
Rear overhang is measured from the center of the rear axle to the furthest rearward point of the body. Drop a plumb line from the rear bumper, tray or tow bar to the ground and mark it. Measure the horizontal distance from the rear axle center to that mark.
Decide which rear point counts before you start, since a tow bar, a tray or a bike rack can sit further back than the body. Measure the body point and the accessory point separately. That way you can report the figure that matches the rule or the listing you are comparing.
On a ute, the rear overhang often grows when a tray or a long tow bar is fitted. Check whether the tray sits behind the original body line and measure to its rearmost edge. Note the accessory fitted at the time of measurement so the figure can be understood later.
What sets the maximum overhang
Maximum overhang depends on the vehicle class, its gross mass, the body type and the regulations where it is registered. A rule for a passenger car does not transfer to a heavy truck or to a ute. The same vehicle can have a different limit in another jurisdiction.
Design also sets a practical limit, because a long overhang swings wide in a turn and can scrape on a steep driveway. Departure angle, the slope a vehicle can leave without touching, shrinks as rear overhang grows. Approach angle at the front behaves the same way.
UK regulations and other national rule sets each define overhang in their own terms. Confirm the figure in the rule set that applies to the vehicle and the load you plan to carry. Do not copy a limit from another country or another vehicle class.
- Vehicle class and gross mass
- Body type and fitted accessories
- The regulation set that applies where the vehicle is registered
- Load carried beyond the body
- Approach and departure angle needs
Maximum overhang on a ute
A ute has no single maximum overhang figure that applies to every model and every place. The limit comes from the vehicle's class, its rated mass and the rules of the jurisdiction. The tray length, the tow bar and any rear rack all change the measured figure.
When you compare utes, note the rear overhang with the standard body and again with the tray you plan to fit. A longer tray can push the rear point well past the factory line. Carry that figure into your shortlist so each listing sits beside a measured number.
A load that hangs past the rear of a ute is a separate case from body overhang. Marking and load restraint rules apply to the projection, and they differ from the body overhang limit. Check both figures before you plan a trip with a long load.
Accessories that change the rear figure
Tow bars, trays, ladder racks and bike carriers can all extend the rear-most point of a vehicle. Each accessory adds length that a body-only measurement misses. Measure the accessory edge and record it with the name of the item fitted.
A tow ball sits behind the bumper and is easy to overlook when the tape runs along the body. Project the tow ball down to the ground with the plumb line and measure to that point separately. Keep the two figures apart so a comparison is not muddled.
Removable accessories change the figure the moment they come off. Note whether the measurement was taken with the item fitted or removed. Anyone reading the figure later needs that detail to use it properly.
Recording figures for a shortlist
A clean record of each vehicle turns scattered figures into a shortlist you can compare. List the front overhang, the rear overhang, the accessories fitted and the rule set you checked. Keep the measurement date and the ground condition with the entry.
Put each vehicle in its own row with the same fields, so a difference stands out. A table of front and rear figures beside the body type and the gross mass shows which vehicle suits your needs. Add the maximum figure and the margin between measured and allowed.
Bring your own measurements rather than relying on a listing claim alone. A seller's figure may have been taken with a different accessory or a different reference point. Your own numbers give the shortlist a consistent basis.
Questions about vehicle overhang
How do I do a vehicle overhang measurement at home?
A vehicle overhang measurement needs level ground, a tape and a plumb line. Drop the plumb line from the furthest body point at each end and mark where it meets the ground. Measure from the axle center to each mark and record the front and rear figures separately.
What is the maximum overhang on a vehicle?
The maximum overhang on a vehicle depends on its class, gross mass, body type and the regulations where it is registered. No single figure covers every vehicle. Check the rule set that applies to your vehicle and load before you rely on a number.
What is the maximum overhang on a ute?
A ute has no universal maximum overhang figure, because the limit follows the vehicle's class, mass rating and local rules. The tray, tow bar and rear rack all change the measured rear overhang. Measure your own ute with the accessories fitted and compare that figure to the rule that applies.
What is the maximum overhang on a vehicle in the UK?
UK regulations set overhang limits that depend on the vehicle class and its dimensions. The figure for a passenger car is not the figure for a heavy goods vehicle. Confirm the current requirement for your vehicle class in the UK rule set before you modify a body or add a rear accessory.
Does a tow bar count toward rear overhang?
A tow bar can sit further back than the body and extend the rear-most point. Measure to the tow bar separately from the body so both figures are recorded. Report which accessory was fitted when the measurement was taken.
Why does long rear overhang matter when driving?
Long rear overhang swings wider in a turn and reduces the departure angle at slopes and ramps. A vehicle with a long rear overhang can scrape its tail on a steep driveway. Measure the overhang before you plan routes with tight turns or steep ramps.
Read next
-
Find vehicle dimensions by registration number
-
Updating vehicle details with government agencies
-
Car seating configurations and seating charts
-
Car paint thickness gauges: meters, pens and readings
-
Seven-seat vehicles: comparing seating capacity across types
-
Finding a car power inverter near you
-
Small car comparison charts
-
Extract specifications from car listings
-
MPV passenger space and capacity
-
Free car specification checks