How to calculate fuel consumption
Learn how to calculate fuel consumption from an odometer reading and a fill-up, then convert the result to litres per 100 km, km per litre or MPG.
Contents
- Start with a full-to-full fill-up
- The fuel consumption formula
- Litres per 100 km and km per litre
- Work out consumption by mileage
- Convert to miles per gallon
- Average fuel consumption over several tanks
- Compare cars with the same method
- Mistakes that skew the result
- Fuel Consumption Questions Answered
- How do I calculate fuel consumption per litre?
- How much fuel does a car use per 100km?
- How do I work out fuel consumption per mile?
- Can a fuel consumption calculator handle the conversion for me?
- Why does my calculated average differ from the published figure?
- How many fill-ups should I average for a reliable figure?
You calculate fuel consumption by dividing the fuel you put in by the distance you covered since the last fill-up. A full-to-full method gives a reliable figure, and a simple formula turns it into litres per 100 km, kilometres per litre or miles per gallon. The same arithmetic works for any vehicle you want to compare.
- Fill the tank to the same point twice and record the odometer at each fill to get a true fuel consumption figure.
- Divide litres used by distance, then multiply by 100 to express the result as litres per 100 km.
- Divide distance by litres used to get kilometres per litre, or use the MPG formula for miles and gallons.
- One tank gives a rough number; averaging several fill-ups smooths out driving conditions and gives typical fuel consumption.
- Use the same method for every car on your shortlist so the fuel economy figures sit side by side.
Start with a full-to-full fill-up
Fuel consumption measurement begins at the fuel pump, not in a brochure. Fill the fuel tank until the pump clicks off, then write down the odometer reading and the tripmeter value. This first fill is your baseline, and the fuel added here is not counted as fuel used.
Drive as you normally would until the tank is low, then return to the same pump and fill to the same click-off point. Record the odometer again and keep the receipt showing the litres used. Filling to the same point each time keeps the measurement consistent, because a tank filled to a different level changes the result.
The fuel you added at the second fill is the fuel used over the distance between the two readings. Subtract the first odometer value from the second to get the distance travelled. This full-to-full method is the basis of every calculation that follows.
The fuel consumption formula
The fuel consumption formula is fuel used divided by distance travelled. Feed it litres and kilometres to get litres per kilometre, or gallons and miles to get gallons per mile. The raw result is a small decimal, so you scale it to a unit people read easily.
Distance travelled comes from the odometer difference, and fuel used comes from the pump receipt. Keep both numbers in the same measurement system before you divide. Mixing miles with litres or kilometres with gallons gives a figure that means nothing.
Write the formula down once and reuse it for every fill-up you record. A notebook or a spreadsheet holds the numbers and shows the pattern across tanks. The formula stays the same whatever vehicle you measure.
Litres per 100 km and km per litre
Litres per 100 km is the standard way to express fuel use per 100 km in many markets. Divide litres used by kilometres travelled, then multiply by 100. A car that burns 8 litres over 100 km returns 8 L/100 km.
Kilometres per litre works the other way around. Divide kilometres travelled by litres used to get km per litre. A higher km per litre figure means less fuel for the same distance, while a higher L/100 km figure means more.
Choose one unit and stay with it when you compare cars. Litres per 100 km falls as efficiency improves, and km per litre rises, so the two scales move in opposite directions. Converting between them is a division away.
Work out consumption by mileage
Calculating fuel consumption by mileage uses the odometer as the distance source. Note the odometer at a fill-up, note it again at the next fill-up, and subtract the smaller number. That difference is the mileage covered on the fuel you bought in between.
A tripmeter makes this easier because you can reset it at each fill and read the distance directly. Reset the tripmeter at the same moment you record the odometer. The two readings then agree, and the tripmeter distance is the mileage for the formula.
Odometer readings drift if a tire size differs from the original specification. A speedometer and odometer calibrated for one tire size overstate or understate distance when tires change. Treat the figure as a close estimate rather than an exact measurement.
Convert to miles per gallon
MPG expresses fuel economy as miles travelled per gallon used. Divide miles travelled by gallons used to get MPG. The result depends on whether you use US gallons or imperial gallons, because the two gallons hold different volumes.
L/100 km and MPG conversion needs a fixed factor because the units are inverted. Convert litres to gallons and kilometres to miles first, then apply the MPG formula. Keep the gallon type consistent or the comparison misleads.
A fuel economy calculator car tool does this arithmetic for you when you enter distance and fuel. Enter the numbers from your own receipts rather than a published figure. Your own MPG reflects your driving and your routes.
Average fuel consumption over several tanks
Average fuel consumption comes from adding the fuel and the distance across several fill-ups. Total the litres used and total the kilometres travelled, then divide. Averaging the individual tank results instead gives a different and less reliable number.
A single tank can mislead because a long highway run and a week of short trips burn fuel differently. Three to five fill-ups smooth out those swings. The pooled total is the figure to quote when you compare vehicles.
Keep every receipt and every odometer reading in one place. Note the driving conditions alongside each entry so you can explain a sudden change. Cold starts, heavy loads and tire pressure all shift fuel use per 100 km.
Compare cars with the same method
A side-by-side comparison only works when every car is measured the same way. Record distance and fuel for each vehicle over similar routes and similar loads. Then put the results in one table with the same unit in every row.
Published fuel economy figures come from standardized test cycles, so they rarely match real driving. Use them as a starting point and replace them with your own measurements where you can. Your figures reflect the roads and conditions you actually face.
Build a shortlist by listing each car with its measured L/100 km or MPG, its tank size and the kind of driving it covers. Tank size tells you range, while consumption tells you running cost per distance. Both belong in the comparison.
Mistakes that skew the result
A partially filled tank breaks the full-to-full rule and throws the figure off. Always fill to the same click-off point at both ends of the measurement. Skipping this step makes the litres used figure unreliable.
Pump shut-off varies between pumps and between nozzles, so small differences are normal. Averaging several tanks absorbs that variation. Do not chase precision beyond what the pump can deliver.
Recording the wrong odometer digit or forgetting a fill-up distorts the total. Check the subtraction twice and keep the receipts together. A single arithmetic slip travels through every later comparison.
Fuel Consumption Questions Answered
How do I calculate fuel consumption per litre?
Fuel consumption per litre is not a standard unit, because consumption measures fuel against distance, not against fuel. Divide the distance travelled by the litres used to get km per litre instead. That figure tells you how far the car goes on each litre.
How much fuel does a car use per 100km?
Fuel use per 100 km depends on the car, the route and the load, so no single figure fits all. Measure it by dividing litres used by kilometres travelled and multiplying by 100. Your own full-to-full measurement is the number that applies to your car.
How do I work out fuel consumption per mile?
Fuel consumption per mile is litres used divided by miles travelled, which gives litres per mile. Multiply by the number of miles you want to express, or convert to MPG by dividing miles by gallons. Whichever unit you pick, keep it consistent across your comparison.
Can a fuel consumption calculator handle the conversion for me?
Yes, a fuel economy calculator converts between L/100 km, km per litre and MPG once you enter distance and fuel. Enter your own odometer and receipt figures rather than a published rating. Check that the calculator uses the same gallon type you measured with.
Why does my calculated average differ from the published figure?
Published fuel economy figures come from a standardized test cycle, while your average comes from real roads, weather and driving habits. Short trips, cold engines and heavy loads raise fuel use above the test result. Treat the published figure as a reference point, not a prediction.
How many fill-ups should I average for a reliable figure?
Averaging across several fill-ups gives a steadier figure than a single tank. Pool the total litres and total distance rather than averaging each tank result. More tanks reduce the effect of one unusual journey.