# Gear ratio comparison chart

Learn how a gear ratio comparison chart works, what each column and row shows, how to read gear spacing and top speed per gear, and how to lay out your own table.

A gear ratio comparison chart puts several gear combinations side by side so you can compare the ratio, the spacing between gears and the effect on speed in one view. You read it by finding the ratio column first, then following each row across to see how that ratio changes the output. Building your own chart starts with the ratios you already have and the values you want to check. 

- A ratio chart compares rows of gear combinations against shared columns so differences stand out.
- Gear ratio is output speed divided by input speed, or input turns divided by output turns.
- Gear spacing shows how evenly the steps between gears are spread across the ladder.
- Top speed per gear depends on the ratio, the tire size and the engine or motor speed limit.
- A clear layout keeps units in the header and one gear set per row.
 

## What a gear ratio comparison chart shows 

A gear ratio comparison chart is a table that places several gear combinations next to each other for direct comparison. Each row holds one combination, and each column holds one property of that combination. The chart exists so you can see differences at a glance instead of calculating each setup separately. 

The chart works because the same columns apply to every row. A ratio column, a spacing column and a speed column let you compare setups on equal terms. Without shared columns, a side by side comparison becomes a set of separate notes. 

A gear ratio table answers a narrow question well when the columns match your decision. Deciding between two final drives needs ratio and speed columns, not a full geometry sheet. Choose the columns before you fill in any numbers. 

## Reading ratio and turns in the chart 

Gear ratio expresses how many input turns produce one output turn, or the reverse depending on the convention on the sheet. Check the header label first, because a chart that mixes the two directions gives misleading results. Write the convention into the column heading so every reader applies it the same way. 

A ratio of input turns to output turns above one means the output turns slower than the input. A ratio below one means the output turns faster, which happens with overdrive gearing. Reading the number in context matters more than the number alone. 

The gear ratio chart reading step is simple once the convention is fixed. Find the row for the setup you care about, then read across to the columns that matter for your decision. Compare rows only on columns that use the same units. 

## Understanding gear spacing and the gear ladder 

Gear spacing chart values show how far apart consecutive gears sit in ratio terms. A gear ladder lists the gears in order from low to high so the steps between them are visible. Even spacing keeps the drop in output speed similar at each shift. 

Spacing is judged by the ratio between one gear and the next, not by the arithmetic difference. Two gears close in ratio number feel close together in use. A wide step at the top of the ladder often shows up as a large speed drop after a shift. 

A spacing column makes the gear ladder readable at a glance. Add the step between each gear and the gear below it, then scan the column for the largest and smallest steps. That scan shows where the ladder is tight and where it opens up. 

## Top speed per gear and what drives it 

Top speed per gear in a chart is a calculated value, and the chart should say which inputs produced it. Ratio, tire size and the maximum input speed set the result together. Change any one of them and the whole speed column shifts. 

A speed column is only as good as its stated assumptions. Note the tire size and the input speed limit in the header or a footnote under the table. A reader who cannot see the assumptions cannot judge whether the row applies to their setup. 

Top speed per gear is a limit of the gearing, not a promise about real travel. Load, terrain and available power all pull actual speed below the calculated figure. Treat the column as a comparison tool between setups, not as a performance claim. 

## Laying out the comparison table 

A comparison table layout works when each column has one job and each row holds one complete option. Put the identifying label in the first column and the numbers after it. Keep units in the column heading rather than repeating them in every cell. 

Order the rows by the value you care about most, such as ratio from low to high. Ordering turns the table into a sorted gear ladder, which is easier to scan than an unsorted list. Leave out columns that no row uses meaningfully. 

Mark calculated cells so readers know which numbers came from a formula. A short note under the table listing the inputs and the formula is enough. Keep the sheet free of merged cells and nested tables, which break sorting and copying. 

## Building your own gear ratio chart 

Build the chart from the information you hold, not from a generic example. List the gear combinations you actually want to compare, one per row. Then choose the columns that answer your question and fill them in. 

A short build order keeps the sheet consistent. Start with the identifier, add the ratio, then spacing and speed. Check the units on every column before you compare any two rows. 

Review the finished chart for one thing only: whether each row stands alone. A reader should understand any row without reading the neighbors. If a row needs context from another row, move that context into a column. 

- List each gear combination as its own row.
- Fix the ratio convention and write it in the header.
- Add a spacing column for the step between gears.
- Add a speed column with its inputs stated.
- Order rows by ratio or by the value you compare.
- Check units across every column before comparing.
 

## Avoiding errors when comparing gear options 

The main error in a gear ratio comparison chart is mixing conventions between rows. A row using input to output sits beside a row using output to input, and the comparison collapses. Fix the convention once and apply it to every row. 

A second error is comparing speed values built on different inputs. Tire size and input speed limit must match across rows, or the speed column says nothing about the gearing. State the shared inputs above the table. 

A third error is overloading the sheet with columns nobody reads. Each extra column adds a chance of a unit mistake. Keep the table to the columns your decision needs, and put secondary data in a separate sheet. 
| Chart problem | What it looks like | How to fix it | 
| Mixed ratio convention | Some rows read input to output, others the reverse | Set one convention in the header | 
| Unstated speed inputs | Speed column with no tire size or input limit | List shared inputs above the table | 
| Too many columns | Cells with units repeated in every row | Keep units in headings only |  

## Keeping the chart useful over time 

A gear ratio comparison chart stays useful when it records what each number depended on. Inputs change, and a chart without them cannot be updated safely. A note under the table protects future readers from stale values. 

Date the sheet when it is built and note the source of the inputs. When an input changes, recalculate the affected columns rather than editing single cells. The chart then remains a single consistent comparison. 

Keep one chart per question, not one chart for everything. A sheet built to compare spacing between gears serves a different purpose from one built around top speed per gear. Separate sheets stay readable and easier to check. 

## Questions about gear ratio charts 

### How do I read a gear ratio comparison chart? 

Read a gear ratio comparison chart by fixing the ratio convention in the header, then following one row across the columns that matter. Compare rows only on columns measured in the same units. A spacing column and a speed column add context once the ratio column is clear. 

### What does a gear spacing chart tell me that a ratio column does not? 

A gear spacing chart shows how far apart consecutive gears sit in ratio terms, which the ratio column alone does not reveal. Even spacing keeps the drop in output speed similar at each shift. Spacing is judged by the ratio between one gear and the next, not by the difference in ratio numbers. 

### What determines top speed per gear in a comparison table? 

Top speed per gear depends on the ratio, the tire size and the maximum input speed used in the calculation. The chart should state all three so a reader can tell whether a row applies to their setup. Load and terrain pull real speed below the calculated figure. 

### What is the right comparison table layout for gear ratios? 

A workable comparison table layout puts one gear combination per row and one property per column, with units in the headings. Order rows by ratio so the sheet reads as a sorted gear ladder. Avoid merged cells, which break sorting and copying. 

### Can I build a gear ratio table from my own information? 

Yes, a gear ratio table built from your own listed combinations and inputs answers your question more directly than a generic example. List each combination as a row, set the ratio convention, and add spacing and speed columns. Check units across every column before comparing rows.
